Glock slide safety

Glock slide safety DEFAULT

(photo and text by Miles Vining)

Trials Glock with thumb safety

One of the more revolutionary and innovative features of the Glock series of handguns is in their signature slogan “GLOCK Safe Action”. This is based on the fact that although there is no external hand operated safety device, there are three internal ones: trigger safety, firing pin safety, and sear safety. This has paved the way in modern day handgun designs to put the responsibility of firearms handling upon the user and not on an arbitrary lever. There is also the tactical requirement of readily getting the gun into action. But was there ever even an experimental Glock made with an external safety? During the initial Austrian Army trials of 1982, the Army wasn’t used to the fact that a military weapon could be issued without an external safety. So the Army requested a trial pistol with one and sure enough, Glock produced one for them to examine. The conclusion was that it was not needed, but one of these pistols exists today in the National Firearms Center, Leeds, England. Formally known as the MoD Pattern room, the author found this external safety Glock in one of the handgun drawers. The pistol has a newer magazine with extended floorplate so the original magazine must have been mismatched.

Sours: https://www.forgottenweapons.com/thumb-safety-glock/

Manual Safety for Glock – Tactical Safety System for Glock by RDIH

MUST READ PRIOR TO USE!

RDIH Tactical Safety System for Glock 

MOUNTED MANUAL SAFETY – INSTALLATION GUIDELINES

The Tactical Safety System for Glock pistols, by RDIH, should be installed on “stock” Glock Pistols ONLY.  SPECIFICALLY, THE MOUNTED MANUAL SAFETY SHOULD NOT BE ADDED TO ANY GLOCK PISTOL WHERE THE “CONNECTOR” OR ANY PART OF THE FIRING MECHANISM HAS BEEN ALTERED IN ANY WAY.

PERSONS INSTALLING THE MOUNTED MANUAL SAFETY DEVICE ARE SOLELY RESPONSIBLE FOR SAFELY TESTING THE FUNCTION OF THE MOUNTED SAFETY DEVICE, PRIOR TO ANY AMMUNITION BEING INTRODUCED INTO THE FIREARM. 

THE FOLLOWING INSTALLATION AND SAFETY TESTING PROTOCOL IS INTENDED FOR GUNSMITHS, PISTOLSMITHS, AND PERSONS KNOWLEDGABLE ABOUT ALL FUNCTIONS OF THE GLOCK PISTOL AND QUALIFIED TO INSTALL THE MANUAL SAFETY DEVICE. 

SAFETY TESTING PROTOCOL:

  1. REMOVE MAGAZINE AND completely clear the pistol of all ammunition and lock back the slide using the slide stop.
  2. Completely remove ammunition from all magazines. Remove all ammunition from the room to a secure location.
  3. Remove original Glock Slide Backplate, and replace with Mounted Safety Deveice of the TSSG per the enclosed instructions.
  4. Release the slide lock allowing the slide to move forward into battery.
  5. Move the Manual Safety Control Arms UP AND DOWN, and allow to remain in the “down” or Fire position
  6. With no magazine in the pistol, pull back the slide to re-check that pistol is “clear” (barrel is empty and free of ammunition – allow slide to return to battery
  7. With pistol pointed in a safe direction, pull the trigger. You should hear an audible “click” of the striker being released, and the Trigger will remain in the rearward position.
  8. Completely cycle the slide. Trigger should return to the forward position.
  9. Move the arms of the manual safety device to the “UP” or On-Safe Position.
  10. Pull on the trigger. There should be no audible “click” of the striker being released and the trigger should return to it’s fully forward position after being pulled.  Pulling the trigger multiple times should have the same result as the first trigger pull with safety in the “UP” or On-Safe Position, with the trigger returning to the fully forward position after each pull.   
  11. If the Safety Test results were as described in Steps 8 – 11, the device is working as intended.

HOWEVER, ANY TEST RESULT THAT IS NOT CONSISTENT WITH THE EXPECTATIONS DETAILED IN STEPS 8 – 11 ABOVE, INCLUDING BUT NOT LIMITED TO: “STRIKER RELEASES AS A RESULT OF A TRIGGER PULL WITH THE DEVICE IN THE ON-SAFE POSITION”, DEVICE MUST BE REMOVED FROM THE PISTOL AND ORIGINAL SLIDE BACK-PLATE REPLACED.  IT IS PROBABLE THAT THIS GLOCK PISTOL HAS BEEN ALTERED AND / OR THE CONNECTOR, OR OTHER INTERNAL PART IS NOT OEM AND TSSG SHOULD NOT BE UTILIZED UNTIL PISTOL HAS BEEN FULLY INSPECTED BY A GUNSMITH, PISTOLSMITH, OR ARMORER.

  1. Next, with the slide forward and the Mounted Safety Device in the “On Safe” position, retract the slide fully rearward allowing the slide to return to battery. The arms of the device remain in the “On Safe” position.  Moving the slide slightly rearward (approximately ¼”) and back to fully forward position produces same result, the arms of the device remain in the “On Safe” position.  Any result that does not fulfill this expectation requires removal of the Mounted Safety Device from the Glock Pistol, and restoration of the original back plate. 

IN THE EVENT OF ANY MALFUNCTION OF THIS DEVICE,

USER MUST CONTACT BHSpringSolutions LLC IMMEDIATELY

BY SENDING AN EMAIL TO: [email protected].

IT IS THE RESPONSIBILITY OF THE USER OF THIS PRODUCT TO TEST, WITH SUFFICIENT FREQUENCY, ALL ASPECTS OF FUNCTION OF HIS/HER FIREARM, AND TO ASSURE THAT THE FIREARM RECEIVED PROPER MAINTENANCE AND PERIODIC INSPECTION BY A GUNSMITH, PISTOLSMITH, OR ARMORER.

IT IS THE RESPONSIBILITY OF THE USER TO FOLLOW ALL SAFE FIREARMS HANDLING PRACTICES AND FOLLOW THE INSTRUCTIONS CONTAINED WITH THE TESTING PROTOCOL DESCRIBED HERE.  AND WITH THE EXCEPTION OF CARRYING OUT THIS TESTING PROTOCOL:

NEVER HAVE YOUR FINGER ON THE TRIGGER OF ANY FIREARM UNTIL YOU ARE READY TO FIRE THE WEAPON.  

FOR ALL PURPOSES OF COMPLETING THE SAFETY TESTING PROTOCOL DESCRIBED HEREIN, OR FOR PURPOSES OF PRACTICE (DRY-FIRING), ALWAYS OVERIMPLIMENT ALL SAFETY PRECAUTIONS AND ONLY IN A CONTROLLED ENVIRONMENT.  OTHERWISE, DO NOT HAVE YOUR FINGER ON THE TRIGGER OF ANY FIREARM, EVER, FOR ANY REASON, UNTIL YOU INTEND TO FIRE THE WEAPON. 

NEITHER RDIH, BHSpringSolutions LLC, nor any officers, employees, or affiliates of either company, represent or warrant that an “Unintended Discharge” will not, or cannot happen when utilizing the Tactical Safety System for Glock pistols.  Utilization of the Tactical Safety System for Glock (TSSG) adds margins of safety/safeguards to the Glock design in the event of human error – but does not and cannot safeguard against all human errors, nor can any safety margins safeguard against the possibility of Unintended Discharge due to mechanical failure or lack of sufficient maintenance including periodic servicing and evaluation of a firearm by a qualified Gunsmith or Pistolsmith.  ANYTIME a round of ammunition is chambered in the barrel of any firearm, the possibility of an Unintended Discharge greatly increases. 

Sours: https://bhspringsolutions.com/index.php/product/unintended-firearms-discharge-stopped-tactical-safety-system-for-glock-by-rdih/
  1. Asian cheats
  2. Vermont pbs jobs
  3. Line card cisco
  4. Simply floors reviews

OUR SAFE ACTION® SYSTEM.

Always Safe and Always Ready

OUR SAFE ACTION® SYSTEM.

GLOCK’s revolutionary SAFE ACTION® System provides a consistent trigger pull from the first to the last round. The three automatic independently-operating mechanical safeties are built into the fire control system of the pistol.

This safe, simple, and fast system allows the user to concentrate fully on shooting without having any additional actions to disengage and reengage safeties. This means it is safe if it’s dropped, and additionally it functions at temperatures from -40° to 122° Fahrenheit.


How Does it Work?

The SAFE ACTION® System is a fully automatic safety system consisting of three passive, independently operating, mechanical safeties. All three safeties disengage sequentially as the trigger is pulled and automatically re-engage when the trigger is released.

Safe action


The trigger safety is the first safety in the firing sequence. It’s incorporated into the trigger in the form of a lever and when it is engaged blocks the trigger from moving rearward. To fire the pistol, the trigger safety and the trigger itself must be deliberately depressed at the same time. If the trigger safety is not depressed, the trigger will not move rearwards and allow the pistol to fire.

The trigger safety is designed to prevent the pistol from firing if it’s dropped or if the trigger is subjected to any pressure that isn’t a direct firing pull.

WARNING: If the trigger is in the forward position the pistol may be loaded.

The second safety, the firing pin safety, mechanically blocks the firing pin from moving forward in the ready-to-fire condition. As the trigger is pulled rearward, the trigger bar pushes the firing pin safety up and frees the firing pin channel. If you decide not to fire and release the trigger, the firing pin safety automatically reengages.

The final safety involves the trigger bar, which rests on the safety ramp within the trigger mechanism housing. The trigger bar engages the rear portion of the firing pin and prevents the firing pin from moving forward. As the trigger is pulled rearward the trigger bar lowers down the safety ramp and allows the release of the firing pin. After firing, the trigger bar moves upward and re-engages the firing pin. As the trigger is released, all safeties automatically reengage.

A special feature of the SAFE ACTION® System allows the trigger to reset with only limited forward movement of the trigger, so you don't have to completely release the trigger in order to fire a second controlled shot or when you need to fire several rounds quickly. After a round is fired, you only have to release the trigger until it resets, which you can hear and feel.

All three pistol safeties automatically re-engage when you release the trigger to its forward position.

Sours: https://us.glock.com/en/learn/glock-pistols/safe-action-system
How the Glock \

'' I'll take a look, '' Lenka said in a non-questioning tone and, bending over, added, Hello, Evgenia Evgenievna. '' You can touch it, as if I objected. to my ass. Running her finger between the halves, she shoved it into my hole. "Yes, a shameless girl," I thought.

Safety glock slide

I didnt understand nifiga, but I didnt give this meaning much as I was busy Nicole's panties. Dressed on prettier, I went to her, grabbing her panties. I was lucky I found her, but apparently she was asleep. She opened the door, she was a T-shirt with a deep cut, and short shorts.

How the Glock \

A sound. Vitya finished yet I heard. - Where are you.

You will also be interested:

And she trustingly lifted her shirt, revealing and caressing her tender and beautiful body. She wanted me so badly, waited so long for me that she got wet through and showed it to my eyes. Her shirt was just getting in our way now.



11066 11067 11068 11069 11070