Rock buggy frame

Rock buggy frame DEFAULT

Rock Bouncer Chassis

Typical Lead Time: 4 - 6 weeks

Hammer Down for Longer

Our Heavy Duty (HD) design places 1.75 x .188 wall tubing in the high impact areas where extra strength is needed.

A chassis built entirely out of .120 wall tubing will keep occupants safe in a roll over, but leaves the chassis vulnerable to getting dented and bent. The increased strengthening of a few key impact areas allows the chassis to have a better chance of remaining straight and is less likely to dent from sudden impacts. A heavy duty chassis only adds a minimum amount of weight and you’ll have a chassis that will hold up for years to come.

For specific tubing sizes used to build this chassis and their location, reference these images:

Rock Bouncer Chassis Tubing Size 1Rock Bouncer Chassis Tubing Size 2Rock Bouncer Chassis Tubing Size 3Rock Bouncer Chassis Tubing Size 4

Sides are Protected with Replaceable .188 Tubing Rock Sliders

.188 wall rock sliders act as protection to the sides of your Rock Bouncer. They also double as a step to ease entry and exit from your buggy if you have not chosen to have doors installed. We’ve built these into the chassis that if they do get beat up, they can be easily cut off and replaced with new .188 TubingRB Rock Sliders

.188 wall rock sliders act as protection to the sides of your Rock Bouncer. They also double as a step to ease entry and exit from your buggy if you have not chosen to have doors installed. We’ve built these into the chassis that if they do get beat up, they can be easily cut off and replaced with new .188 Tubing

RB Rock Sliders

 

Adequate Rear End Room for Fuel Cell and Tool Box/Cooler

Easily fit a 15 gallon fuel cell and a fabricated tool box in the rear end. Have fun trail riding and bring along a few tools that you may need. Or use the tool box as a cooler for your beverages and food.

 

Install and Remove Components with Ease

Removable Crossmembers allow for easily installing and removing of drive train components into the chassis. These tubes are connected using our Tube Flange sets.RB Removable Crossmembers

Removable Cross members allow for easily installing and removing of drive train components into the chassis. These tubes are connected using our Tube Flange sets.

RB Removable Crossmembers

Correct 4 Link Installation Every Time

The chassis was designed for Proper 4-link Geometry and accepts the most popular axle configurations. Hesitant that it won't fit yours? We can let you know for sure. Email us at [email protected] or give us a call at (615) 962-9135 to confirm.

 

Beautiful and Professional MIG Welded Fabrication

Our MIG welds are more than just strong, they are professional and good looking also. Our fabricators have years of experience welding onto our chassis and have developed the quality you’d expect from a professional facility. You get reliability and a great looking rig.

 

Full Support throughout your Build

When you purchase a Wide Open Design chassis, you are also purchasing full build support and guidance. We’ve built a large amount of buggies starting from our chassis and can answer pretty much any question you have in the process. We also have designed and manufactured components specific to our chassis to reduce guesswork and guarantee a great end product.

 

Build your Dream Rock Bouncer!

If there are modifications you may want done to the chassis, we may be able to do it! For a quote on chassis configuration, rolling chassis or turn-key vehicle please email [email protected] or give us a call at (615) 962-9135 with your ideal specifications.

 

Technical Specifications:

  • Wheel Base - 113" to 125"
  • Widest Point - 55"
  • Weld Type - MIG
  • Main steel structure construction - 1 3/4"x.120 wall DOM steel tubing
  • The lower bars at the belly pan construction - 1 3/4"x.188 wall DOM steel tubing
  • Rocker bars construction - 1 3/4" x .188 wall DOM steel tubing

 

Available Added Options:

 

Rock Bouncer X Tubing Size 4

Check Out Buggy Galleries that use this Chassis:

Sours: https://www.wideopendesign.com/rock-bouncer-chassis

Rock Crawler Buggy Frame Powder Coated in Ink Black

Added To Cart

image coming soon

{{ itemJustAddedToCart.product.name }}
Some powders may require either a base coat or a top coat or have other special instructions. Please read each product description carefully to ensure you are ordering what you need. Amount:{{ pricePerUnit }}/unit    Quantity:{{ data.quantity.value }} {{ data.quantity.unit }}

{{ itemJustAddedToCart.product.data.name }} is temporarily out of stock
Swatches are powder coated aluminum panels for accuracy. If your order contains an "Out of Stock" swatch, we will create that swatch for you, then ship your entire swatch order. This can take up to two weeks.
If all swatches are IN STOCK it will ship in 1-3 business days via UPS overnight.

Items are Added to Your Cart

Sours: https://www.prismaticpowders.com/gallery/9011/rock-crawler-buggy-frame-powder-coated-in-ink-black
  1. Counselor kjv
  2. Warhammer datacards
  3. Sprite maker danganronpa
rock racer - American Rock Rods    off road buggy - American Rock Rods    off road buggy - American Rock Rods

We have produced a wide array of chassis types and variations since we started. We feel our designs have progressed, and evolved into better looking, safer, and more functional chassis. While our competitors copy some of our older designs, we have moved on to what we consider a superior product.

rock buggy - American Rock Rods     

 

 mantis

The Mantis chassis series is unique in it's approach to the end builder and in function. The Mantis chassis is designed with a more fundamental format than American Rock Rod's other chassis styles. This means that several attributes such as coil over, radiator mounts and floor bars are not included in the base models, but optional. This allows the builder to acquire a principal platform at a less comparable price to our other chassis types. This leaves opportunity for you to add your own tube work and personal flare. For an end result that can be more customized with the security of knowing your base chassis is dimensionally and anatomically positioned correctly. We have several key straight tubes that we recommend, and they can all be added with just a simple notcher and chop saw. No tube bending required.

rock crawling chassis

THE MANTIS 2:The Mantis 2 chassis is a front engine off road buggy that seats two people. The width of the chassis is  48", which is a bit narrower than a typical Jeep. This incredibly agile design makes this rock buggy lighter and exposes less body and frame to drag, hit or hang up on in off road situations. Cab space will accommodate a person of 6' 3" and still have 4" of over head interior head space. The Mantis 2 is an excellent choice for the dirt pilot that wants a smaller but solid chassis for trail rides, competition crawling or rock racing. The front end of our chassis can be setup to accomodate our custom front clip, or narrowed Jeep body panels.

off road buggy Mantis T3

THE MANTIS 3T: The Mantis 3T has not been shown to the public yet as it is still in the design stages. It will be a long wheel base 2 seat chassis with a truck bed back end. The front will almost exactly resemble the front of the Mantis 2, with a tubular and functional bed hanging off the back. This buggy will have a trophy truck look with the ultimate in cargo capacity. Look for this chassis to emerge in 2012!.    

rock crawl chassis

THE MANTIS 4:The Mantis 4 chassis is a front engine off road buggy that seats up to four people comfortably. The width of the chassis is  48", narrower than some of the previous buggies we have built, and the normal dimensions of most smaller factory bodied vehicles. Although the width is narrow, the Mantis 4 chassis is a long wheel base buggy. This means that it's length will require more strategic driving for more difficult trails and larger tires to keep it's undercarriage from hanging up on obstacles. Although you will find that the wheel base can be an advantage on large shelf trails, loose hill climbs and the big bowls of Moab. Fit is perfect for anyone up to 6'3". This off road chassis is the perfect choice for the wheeler that is looking for a family buggy that still wants some of the advantages of a smaller dimensioned machine.      

brawler

The Brawler chassis is still in the early design stages! It will be a 2 seat, rear engine competition style buggy.

rock buggy - American Rock Rods

THE BRAWLER 2:This hybrid dessert and rock racer is a 2 seat rear engine chassis built from both 2" and 1.75" d.o.m. round tubing to ensure it's safety and long term durability for many years of racing and trail riding. Further, this is the staple base material for a race oriented machines of it's completed weight class. To allow it to compete from the rocks of the Hammers to the Baja peninsula. Engineered to accept coil over single/dual shocks and ORI style strut suspensions.  A side to side dimensions comparable to many of the smaller two seated competition style tube cars in contention today. The Brawler's more intimate interior and exterior creates superior maneuverability and less body to hang up on trail obstacles. Brawler chassis' have their own signature appearance and require American rock rods to craft the front hood and cowl assembly, or a custom built front end coverage is required.       

 

  

unique

Unique chassis builds are the way to have a rock rod that has an exclusive appearance and specific functional capabilities. These off road  chassis' can be commissioned with client input and direction as to these attributes. Examples reflect, special duty vehicles, competition focused machines and simply a vehicle that is one of a kind. If you can sketch it, we can build it, all while keeping it purposeful, functional, and safe.

rock buggy - American Rock Rods

UNIQUE BUILDS: These off road buggies are unlimited in style and function, and are only limited by cost and gravity. If you want an off road machine for a special use or just desire something that is completely uncommon and without a duplicate, this type of chassis is your best choice. Be prepared that build times are typically much longer, costs can easily skyrocket, and more frequent visitations to our facility are required.      

bullet holes - American Rock Rods

Sours: http://www.americanrockrods.com/chassis_types.php
How to Build a Rock Bouncer Chassis

Rock Bouncer X Chassis

Typical Lead Time: 4-6 weeks

The all new Rock Bouncer X Chassis takes the place of our original Rock Bouncer Chassis that we have been building for years. We have redesigned and reworked the chassis to upgrade many aspects of the original.

Upgrades from the original Rock Bouncer chassis:

  • Narrowed and lowered the Dash bar a few inches for increased visibility
  • Design changes for mounting trailing arms and bypass shocks in the rear of the chassis 
  • Narrowed front frame rails to allow for bypass shock clearance
  • Option of two different rear frame rail configurations depending on suspension choice 

We have developed an entire line of parts and accessories to go with this chassis to make building at home easier. For all of the available options for this chassis, call us at 615-962-9135.

As with the original Rock Bouncer, this chassis was designed with the hardcore-trail rider and rock racer in mind. The Rock Bouncer X is made to satisfy the needs of someone looking to conquer the most extreme trails or obstacles. With the upgraded suspension capabilities we can conquer harder trails, drive faster, and ride better than we ever could before.This chassis, like all Wide Open Design chassis, was designed with our experience of rigorous testing and designing vehicles that can pushed to their limits while being a reliable off-road platform. Many available options for the Rock Bouncer's components and configurations make this chassis platform the ultimate foundation for a 4x4 vehicle.

Typical Lead Time: 4 - 6 weeks

Hammer Down for Longer

Our Heavy Duty (HD) design places 1.75 x .188 wall tubing in the high impact areas where extra strength is needed.

A chassis built entirely out of .120 wall tubing will keep occupants safe in a roll over, but leaves the chassis vulnerable to getting dented and bent. The increased strengthening of a few key impact areas allows the chassis to have a better chance of remaining straight and is less likely to dent from sudden impacts. A heavy duty chassis only adds a minimum amount of weight and you’ll have a chassis that will hold up for years to come.

For specific tubing sizes used to build this chassis and their location, reference these images:

Rock Bouncer X Tubing Size 1Rock Bouncer X Tubing Size 2Rock Bouncer X Tubing Size 3Rock Bouncer X Tubing Size 4

Sides are Protected with Replaceable .188 Tubing Rock Sliders

.188 wall rock sliders act as protection to the sides of your Rock Bouncer. They also double as a step to ease entry and exit from your buggy if you have not chosen to have doors installed. We’ve built these into the chassis that if they do get beat up, they can be easily cut off and replaced with new .188 TubingRB Rock Sliders

.188 wall rock sliders act as protection to the sides of your Rock Bouncer. They also double as a step to ease entry and exit from your buggy if you have not chosen to have doors installed. We’ve built these into the chassis that if they do get beat up, they can be easily cut off and replaced with new .188 Tubing

RB Rock Sliders

 

Adequate Rear End Room for Fuel Cell and Tool Box/Cooler

Easily fit a 15 gallon fuel cell and a fabricated tool box in the rear end. Have fun trail riding and bring along a few tools that you may need. Or use the tool box as a cooler for your beverages and food.

 

Install and Remove Components with Ease

Removable Crossmembers allow for easily installing and removing of drive train components into the chassis. These tubes are connected using our Tube Flange sets.RB Removable Crossmembers

Removable Cross members allow for easily installing and removing of drive train components into the chassis. These tubes are connected using our Tube Flange sets.

RB Removable Crossmembers

Correct 4 Link Installation Every Time

The chassis was designed for Proper 4-link Geometry and accepts the most popular axle configurations. Hesitant that it won't fit yours? We can let you know for sure. Email us at [email protected] or give us a call at (615) 962-9135 to confirm.

 

Beautiful and Professional MIG Welded Fabrication

Our MIG welds are more than just strong, they are professional and good looking also. Our fabricators have years of experience welding onto our chassis and have developed the quality you’d expect from a professional facility. You get reliability and a great looking rig.

 

Full Support throughout your Build

When you purchase a Wide Open Design chassis, you are also purchasing full build support and guidance. We’ve built a large amount of buggies starting from our chassis and can answer pretty much any question you have in the process. We also have designed and manufactured components specific to our chassis to reduce guesswork and guarantee a great end product.

 

Build your Dream Rock Bouncer!

If there are modifications you may want done to the chassis, we may be able to do it! For a quote on chassis configuration, rolling chassis or turn-key vehicle please email [email protected] or give us a call at (615) 962-9135 with your ideal specifications.

 

Technical Specifications:

  • Wheel Base - 115" to 122"
  • Widest Point - 55"
  • Weld Type - MIG
  • Main steel structure construction - 1 3/4"x.120 wall DOM steel tubing
  • The lower bars at the belly pan construction - 1 3/4"x.188 wall DOM steel tubing
  • Rocker bars construction - 1 3/4" x .188 wall DOM steel tubing

 

Available Added Options:

 

Rock Bouncer X Tubing Size 4

Check Out Buggy Galleries that use this Chassis:

Sours: https://www.wideopendesign.com/rock-bouncer-x-chassis

Frame rock buggy

At Fabn801, we pride ourselves with quality chassis and accessories. Every product we offer is hand cut, welded, inspected, tested, and fully built in our fabrication shop, located in Utah. Before shipping anything out to you, we go over every item for quality to make sure what you get is what we would want. Whether it be for competing or just having a fun weekend rockcrawling at your local trails.

Our 2.0 RockLizard Chassis

Over-engineered for greater peace of mind.

Fabn801-standard-rock-lizard

The upgraded, over-engineered Standard RockLizard 2.0 is our flagship chassis, built with 1.5” D.O.M. main tube and 1.75” D.O.M. tube from sliders down. If you love offroading and have an average build and height, this is the chassis you’ll want to get.

Fabn801-XL-rock-lizard

The upgraded, over-engineered XL RockLizard 2.0 is our beefier option with 1.75” D.O.M. tube all the way around. Same dimensions as our standard 2.0 option with the plus of thicker tube. If you want more reinforcement this is the chassis for you.

Our Special edition Chassis

For the family oriented build and more!

Fabn801-4-seater-chassis-rock-lizard

The 4-Seater Lizard is the build to get if you’re into raising the next generation in the backseat while crawling hard and safe. Comes standard with the deep belly. This is where the next generation of enthusiasts will get their start.

discontinued.png

Our Komodo Dragon chassis is made out of DOM tube .120 wall; Main structure is all 1.75” and from sliders down it’s 2”. This chassis is longer and taller than our 2.0 chassis to help give YOU the extra room you want.

Fabn801-Baby-rock-lizard-child

The Baby Lizard is one of our specialty chassis, built for those with a smaller build in mind. If you’re looking to give your kids a little more freedom, this is the place to start.

20210608_174029591_iOS.jpg

The Blade chassis was designed for those wanting extra space and easy access, but don’t worry it you are wanting to compete or just enjoy the trails we have different door options to accomodate that!

Accessories

Customize your new chassis with a whole lot less time and headache.

Chassis Side Kit.jpg
fabn801-axle-bracket-kits
Fabn801-Link-kits
Fabn801-Boat Sides
motor mounts
DFBC8BAD-54FB-4B3B-B668-0A7D55E90605 1.JPG
Fabn801-Roof-kit
8D641B62-AE03-4F4F-98E5-4B7A82049A0B.JPG
0F92CA86-8D7A-4822-8A84-A4354417B704 1.JPG
Fabn801-Side-panel-kit
IMG_0252.JPG

Merch

Shirts, stickers and a whole lot of awesome.

 

Sours: https://www.fabn801.com/products
Building A Tube Chassis For Our Bottom Drawer Buggy - Xtreme 4x4 S2, E14

With a bottle of beer in hand, in shorts, in blue rubber slippers. He was already a little drunk, he said that it was his birthday today. He bought more beer and cigarettes, a bag of oatmeal cookies, gathered us and we went to the garden next to the yard. It was already getting dark, it was late, so even though the grandmothers were sitting on the benches in the courtyard, there was not a soul in the kindergarten.

We walked around it to the other side away from the house, so that no one would see that we were drinking beer.

You will also be interested:

This thought hurt Kai so much that he could hardly breathe, and a lump approached the goal. The guy turned around a little and went to Nickys house unnoticed, he made a decision, from which the heart was torn to. Pieces. - "I want to talk" - said Kai, leaving from behind the wall behind which he was hiding, when Veronica came to the door of her apartment.



2133 2134 2135 2136 2137