Ptac control board

Ptac control board DEFAULT

ptac control board kit rskp0006 installation instructions - Amana PTAC

PTAC CONTROL BOARD KIT

RSKP0006

INSTALLATION INSTRUCTIONS

Description

Control boardinstallation procedures are described in detail

in these instructions. Read and follow these instructions

carefully before replacing the controlboard. Failure to do so

may result in controlboard damage.

Electrostatic Discharge (ESD) Precautions

Before removing the new controlboard from the static wrap,

it is very important to discharge any static electricity. This

can be accomplished in two methods. Servicer can wear a

ground strap or by touching the metal chassis before replacing

the board.

Important Note:

Damage to the controlboard can occur from failure to

disconnect power supply or failure to set the master switch

(located on the controlboard) to OFF before removing the

low voltage terminal strip cover from an installed control

board. Damage to this board by not following these instructions

is considered misuse and not covered under either the

standard unit warranty or any extended service contract.

Important Note:

All warranty replaced boards must be returned to the parts

source from which they were purchased to insure proper

warranty credit.

Existing Control Board Removal Procedures

1. Disconnect power to the unit by unplugging the power

cord at the wall outlet or subbase, or disconnect power at

the fuse box or circuit breaker.

2. If the cabinet front is screwed to the chassis, remove the

1/4” screw (or screws) located behind the inlet grille. Pull

the inlet grille forward from the top of the grille to access

screw(s).

FRONT MOUNTING

HOLE

Figure 1

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

ATTENTION INSTALLING PERSONNEL

As a professional installer you have an obligation to know the product better than the customer. This

includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention

to all safety warnings. Often during installation or repair it is possible to place yourself in a position which is

more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough to be able to

instruct a customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting. Most dealers have a list of specific

good safety practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices.

However, if there is a direct conflict between existing practices and the content of this manual, the

precautions listed here take precedence.

IO-660A

November 2006

Printed in USA


ON

1 2 3

LOAD

COM

265

230

3. Remove cabinet front from chassis by tilting the bottom of

the front forward, lifting slightly up and forward.

4. If a remote thermostat or any low voltage accessory is

being used, remove the low voltage pin connector from the

low voltage terminal strip. If a previous version board is

being replaced remove wires from the low voltage terminal

strip.

PULL TO REMOVE

THERMOSTAT KNOB

PULL TO REMOVE

MODE SWITCH KNOB

Lift Off

ESCUTCHEON

SCREW (2)

SCREW

12. The external transformer will come with the Black 37

wires connected to the LOAD terminal of the transformer

(LOAD terminals are the low voltage terminals) and the

Grey 22 wire connected to the COM terminal on the

transformer. The Grey 21 wire will need to be connected

to the 230 or 265 volt tap on the transformer. Place the

control panel back on its hinges.

NOTE: Refer to the serial plate for voltage information.

13. Install the new board and reinstall the screws removed in

step # 8.

14. Using the insulated terminals connect the two (2) Black

37 wires from the Load terminals on the transformer to the

“24VAC Transformer” terminals on the controlboard. See

Figure 4.

15.Connect Grey 22 wire from the COM terminal on the

transformer to line 2 on the controlboard. Connect Grey

21 wire from the transformer to line 1 on the controlboard.

TRANSFORMER

Figure 2

5. Remove knobs and escutcheon.

6. Remove the two mounting screws, one on each side of

controlboard cover. Some models may have a screw on

the lower right side of the control panel that will need to be

removed. Tilt control panel out and remove cover.

7. Remove the wires from the board in the unit, including

Thermistor Sensors if they plug into the board.

8. Remove the four screws holding the board and remove the

old board.

Figure 3

New Control Board Installation Procedures

TRANSFORMER

LINE

BK37

GY22

GY21

BK37

LINE 1 HEATER 1 HEATER 2 LINE 2 COMPRESSOR

9. If existing unit has a remote mounted “off board” transformer

for board power, proceed to Step 13.

10. Lift the control panel up so the control panel is free of its

hinges. Orient the control panel so there is easy access

for mounting components to the inside of the control

panel.

11. Using the two #8 screws that are provided, screw the

transformer that was provided with the kit to the control

panel in the transformer mounting holes provided in the

panel. See Figure 3.

2

24VAC~TRANSFORMER

12VA CLASS 2 ONLY

Figure 4


16. Thermistor Temperature Sensors Installation

A. It is recommended that the Indoor Discharge Thermistor

(with the YELLOW wires) be installed but it is

optional. If you chose not to install this sensor, the

green status light will remain illuminated continuously.

For status light functionality, the YELLOW

thermistor MUST be installed. Instructions are as

follows:

A1. Carefully cut and remove the gasket on the left and

right sides of discharge screen. Remove the two (2)

5/16” screws holding the indoor exhaust screen above

the indoor coil. Remove the indoor exhaust screen.

Remove the two (2) 1/4” screws connecting the heater

panel to the evaporator coil.

Remove the two (2) screws mounting the air baffle to

the top of the heater panel and remove and discard the

air baffle.

A2. Install the new air baffle. Route the yellow thermistor

probe from right to left through the wiring tube enclosure.

Mount the black tip of the yellow thermistor

probe in the plastic clip provided. Hold the plastic

clamp in place and secure the clamp to the left end of

heater panel using one of the original screws. Replace

the screw on the right end of the air baffle being

careful not to damage the wiring insulation on the

probe.

A3. Replace the heater panel, routing the yellow wire

around the right end of the heater panel and into the

control panel pulling snug to prevent the wire from

being entangled in the blower wheel or being visible

from above. Replace the two screws mounting the

heater panel to the evaporator coil.

A4. Replace the exhaust grille and two mounting screws.

A5. Connect the yellow wire using the plug-on connector

to the new board on the IDT (yellow) terminals.

B. If the existing Indoor Ambient Thermistor (with the

BLACK wires) was connected to the board by a plugon

connector, reconnect it to the new board on the IAT

(black) terminals. If the existing Indoor Coil Thermistor

was soldered to the previous board, install the

new black thermistor per Figure 6 and connect as

above.

Clip is designed to be pushed

into the coil between

the aluminum fins

and attach over

two (2) screws.

CLAMP END OF

THERMISTOR

SECURELY

PLASTIC CLAMP

WIRE ENCLOSURE

ROUTE THERMISTOR

THROUGH TUBE ON

BLOWER EXTENSION

YELLOW

THERMISTOR

Figure 6

Figure 5

3


C. If the existing Indoor Coil Thermistor (with the RED

wires) was connected to the board by a plug-on

connector, reconnect it to the new board on the ICT

(red) terminals. If the previous board used indoor coil

bi-metals, remove and discard the bi-metal devices.

The access door will need to be removed on the indoor

coil to gain access to the bi-metal. See Figure 6. The

Indoor Coil Thermistor will need to clip on the vertical

section of the 90-degree bend of the inlet line to the

indoor coil. See Figure 7. Connect the Indoor Coil

Thermistor to the board as noted above.

D. If the existing Outdoor Coil Thermistor (with the

BLUE wires) was connected to the board by a plugon

connector, reconnect it to the new board on the

OCT (blue) terminals. If the previous board used

indoor coil bi-metals, remove and discard the bi-metal

devices. The Indoor Coil Thermistor will need to clip on

the crossover tube shown in Figure 8. There will be

two clips supplied in the kit for the Blue Thermistor.

One clip as supplied on the sensor will fit 5/16” tubing

used on the bent coil, and an additional clip (loose in

the bag) will fit 3/8” tubing used on the flat slab coil.

If you have a slab coil, you will need to remove the 5/16”

clip from the sensor and replace it with the 3/8” tube

clip. Connect the Outdoor Coil Thermistor to the board

as noted above. Outdoor Coil Thermistors are only

used on Heat Pump models; DO NOT INSTALL THIS

SENSOR IF THE UNIT IS NOT A HEAT PUMP.

Figure 8

Cross over tube

for 9,12 and 15k

or center tube for

7,000 BTU

17. If the unit has a condensate pump, go to step 18. If the unit

has a power vent or power door, go to step 19. Otherwise

proceed with step 20. Refer to wiring diagrams in back of

manual.

18. Condensate Pump Units Only

(See Wiring Diagram Page 10

Reconnect the wires across the top terminals of the

controlboard. Connect as follows:

Red 33 to Line 1

Brown 34 to Heater 1

Brown 34 to Heater 2

Power cord (or black 18) to Line 2

Violet 12 and Yellow 3 to Compressor

Black 16 to Fan High

Red 17 to Fan Low

19 from reversing valve and Yellow 1 to Rev. Valve.

Connect the yellow 5 wire to the 230 or 265-volt terminal

as applicable using the piggyback terminal on the yellow

5 wire. Go to step 21.

Figure 7

INDOOR COIL THERMISTOR - RED

All Units

Connect to ICT on Control Board

4


19. Power Vent/Power Door Units Only

(See Wiring Diagram Page 9)

Reconnect the wires across the top terminals of the

controlboard. Connect as follows:

Red 33 to Line 1

Brown 34 to heater 1

Brown 34 to Heater 2

Power cord (or black 18) to Line 2

Violet 12 to Compressor

Blue 4 to Fan high

Blue 15 and Blue 10 to Fan Low

19 from reversing valve to Rev. Valve

Connect the white 7 wire to the 230 or 265-volt terminal as

applicable using the piggyback terminal on the white 7

wire. Go to step 21.

20. Reconnect the wires across the top terminals of the

controlboard. Connect as follows:

(See Wiring Diagram Page 8)

Red 33 to line 1

Brown 34 to heater 1

Brown 34 to heater 2

Power cord or black 18 to line 2

Violet 12 to compressor

Black 16 to Fan High

Red 17 to Fan Low

19 from reversing valve to Rev. Valve.

21. If a remote wired thermostat and an additional REK01B

escutcheon that states “THIS UNIT IS CONTROLLED BY

WALL MOUNTED THERMOSTAT” is used, the knob and

potentiometer will need to be removed. To remove the

knob, loosen the set screw on the side of the knob with

a flat screwdriver and pull knob from potentiometer shaft.

To remove the potentiometer, loosen the nut with a 10mm

driver and remove the nut and 2 washers. Pull the shaft

free of the panel. Reassemble potentiometer, washers,

nut and knob and store for future use. These will be

required if the unit is ever converted back to local controls

instead of wired thermostat operation.

The controlboard cover is now ready to be installed. The

ribbon for the touch pad will need to be connected to the

controlboard. Take caution not to bend or fold the

ribbon (See Figure 9 for ribbon connection).

Install orange connector from the thermostat on the touch

pad to the IHD Terminals on controlboard, unless the

knob has been removed.

Ensure that no wires are pinched or caught between the

cover and the panel and then reinstall the screws removed

in Step 5.

22. If a remote thermostat or any low voltage accessory is

being used connect the low voltage pin connector to low

voltage terminal strip.

If replacing a previous version board you will need to use

the 18 pin connector supplied with the board for low

voltage accessories. Wires supplied with this kit have

terminal ends on the wires. Insert the terminal end into

the correctly labeled slot, push in and it will lock in place.

After loading pin connector use the wire nuts supplied

with the kit to wire nut the new wires onto the existing

wires supplied for low voltage accessories. See Figure 9

on page 5.

23. Set the master switch to ON. Restore electrical power

and verify unit functionality.

24. This control can be configured for several operational

features.

A. If the unit was being controlled by a wired wall

thermostat, the board will have to be configured to

allow the thermostat to operate the unit. To configure

for a wired wall thermostat, press and hold the FAN

SPEED button and press the COOL button twice. The

light in the bottom left hand corner below the OFF light

will blink twice to confirm that the configuration was

successful. Repeat step 24 if the light did not blink.

B. If the unit will be controlled by a wireless thermostat

(Goodman DS01A using DT01A antenna on the unit),

the board may have to be configured to allow the

wireless thermostat to operate the unit. To configure

for wireless operation, press and hold the FAN SPEED

button and press the HEAT button twice. The light in

the bottom left hand corner below the OFF light will

blink twice to confirm that the configuration was

successful. Repeat step 24 if the light did not blink.

C. If constant fan is desired, the unit will need to be

configured by pressing and holding the HEAT button

and pressing the OFF button twice. To revert to auto/

cyclic fan operation, press and hold the COOL button

and press the OFF button twice.

D. Other configuration items exist, but can only be

accessed over the wireless antenna to a wireless site

platform (Goodman DP01A).

E. To reset all the configuration items back to the factory

defaults, turn the master switch off for 10 seconds,

and then hold the HEAT and COOL button while

turning the master switch back on.

25. Replace the front in reverse order as removed in Steps 2

and 3.

5


BROWN

BLACK w/WHITE STRIPE

YELLOW w/BLACK STRIPE

RED

GREEN

WHITE

YELLOW

BLUE

GREEN w/YELLOW STRIPE

Remote Thermostat

*Only load wires needed for accessories attached to unit.

Figure 9

6


REV.

VALVE

YELLOW

FAN

HIGH

FAN

LOW

RIBBON CONNECTOR

DSI IN GL B GH

BLACK

YELLOW

ORANGE from Touch Pad

BLUE

Heat Pump models ONLY.

Must not be used

on PTC models.

LINE 1

RED

24VAC-TRANSFORMER

ON

Left is ON

Position

Figure 10

7


WIRING DIAGRAMS

REMOTE THERMOSTAT OPERATION

COOLING UNIT

W/ELECTRIC HEAT

CONNECT

FUNCTION

R TO:

OFF

-----

HEAT PUMP W/AUXILIARY

ELECTRIC HEAT

CONNECT

FUNCTION

R TO:

OFF

-----

1ST STAGE

ANTICIPATOR

CURRENT: .1

2ND STAGE

ANTICIPATOR

CURRENT: .1

WIRING DIAGRAM

205180 REV.0

FAN

G

FAN

G

COOL

G, Y/W1

COOL

G, Y/W1

HEAT

*

1ST STAGE

HEAT

2ND STAGE

HEAT

G,B,Y/W1

G, W2

* FOR A HEAT PUMP

THERMOSTAT USED

ON A STRAIGHT

COOL UNIT

H

C

F

YL10

OD

FAN/COMP

CAP

RD13

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS

UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

BK37

BK37

7

TRANSFORMER

230

X3

LOAD

265

24VAC~TRANSFORMER

12VA CLASS 2 ONLY

X1

COM

E11 E12

RD33

LINE 1

E1

GY21

1

ELECTRIC

HEATER

HEATER 1 HEATER 2

RIBBED

2 WIRE

G

N

GY22

LINE 2

BK18

S

5

C

R

FUSE

COMPRESSOR

BK16

FAN

HIGH

BR14

RD17

FAN

LOW

20

RE V

VALVE

SOLENOID

E2 E3 E4 E5 E6 E7 E8 E9 E10

K4 K5 K6

CP4

BR34

BR34

CR11

P2

COMP

VT12

P5

WH15

FAN

MOTOR

19

REV

VALVE

K1 K2 K3

P1

P4

X4

IDT

YELLOW

GREEN

3

X2

P9

ICT

RED

P8

OCT

BLUE

ORANGE

SW2

P10

P11

P13

M1

ON / OFF

MASTER SWITCH

COM A

COM B

DS1 DS2 MS1 MS2 EH IN LS FD1 FD2 TF- TF+ C R GL W2 Y/W1 B GH

AUXILIARY

REMOTE THERMOSTATE

IAT

BLACK

M2

6

NOTES:

1

WARNING: DISCONNECT POWER BEFORE SERVICING. W IRING

TO UNIT MUST BE PROPERLY POLARIZED (FOR 265V) AND GROUNDED.

2

RIBBED WIRE MUST BE CONNECTED AS SHOWN

3 ON HEAT PUMP MODELS ONLY.

4 ON UNITS W ITH FRONT DESK CONTROL SWITCH.

5 BK18 ON LINE 2 WITH FUSE SHOWN CONNECTED FOR 265V. FOR 230V & 11

5 V, CONNECT

POWER CORD TO LINE 2.

6 FOR REMOTE OPERATION, SEE CONFIGURATION CHART.

4

FRON T

DESK

SWITCH

USE COPPER

CONDUCTORS ONLY

GN

CHASSIS

1 CONTRO L

PANEL

WIRE LEGEND

7 IF SUPPLY VOLTAGE IS 208V/230V USE THE 230V TAP ON TRAN SFORMER.

IF SUPPLY VOLTA GE IS 265V USE THE 265V TAP ON TRANSFORMER.

115V TRANSFORMER NOT SHOWN.

HIGH VOLTAGE

(FACTORY)

HIGH VOLTAGE

(FACTORY OR FIELD)

8 FOR CONTINUOS FAN OPERATION SEE CONFIGURATION CHART.

LOW VOLTAGE

(FACTORY OR FIELD)

8


265

230

WIRING DIAGRAMS

REMOTE THERMOSTAT OPERATION

FUNCTION

CONNECT CONNECT

R TO:

FUNCTION

R TO:

OFF ----- OFF

-----

FAN

COOL

HEAT

COOLING UNIT

W/ELECTRIC HEAT

G**

G, Y/W1

*

HEAT PUMP W/AUXILIARY

ELECTRIC HEAT

FAN

COOL

1ST STAGE

HEAT

2ND STAGE

HEAT

G**

G, Y/W1

G,B,Y/W1

G, W2

1ST STAGE

ANTICIPATOR

CURRENT: .1

2ND STAGE

ANTICIPATOR

CURRENT: .1

* FOR A HEAT PUMP

THERMOSTAT USED

ON A STRAIGHT

COOL UNIT

** GL- low speed

GH- high speed

H C F

6

POWER

VE N T

MOTOR

VENT

MUFFIN

FAN

LINE

COM

208

240

WIRING DIAGRAM

20518101 REV 0

POWER

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS

UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

BK37

BK37

LINE

COM

X3

24VAC~TRANSFORMER

12VA CLASS 2 ONLY

8

X1

E11 E12

RD33

LINE 1

E1

1

GY21

RIBBED

2 WIRE

GN

ELECTRIC

HEATER

HEATER 1 HEATER 2

YL10

GY22

RD13

COMP

S

R

C

BK18

LINE 2

5

VT12

OD

FAN/COMP

CAP

WH15

BK16

TERMINAL

BLOCK

BR14

RD17

RD14

(PV)

BK17

(PV)

BU4

(PV)

WH7

(PV)

E2 E3 E4 E5 E6 E7 E8 E9 E10

K4 K5 K6

CP4

BR34

BR34

CR11

P2

COMPRESSOR

P5

FAN

MOTOR

FAN

HIGH

FAN

LOW

REV

VALVE

K1 K2 K3

P1

P4

1

4

7

A

WH8

(PV)

X4

IDT

YELLOW

BK11

(PV)

GREEN

ORANGE

2

5

8

BU15

(PV)

X2

3

6

9

B

BK12

(PV)

BU2

(PV)

2

BU9

(PV)

3

1

ON/OFF

SWITCH

BU10

(PV)

3

REV

20

VALVE

SOLENOID

19

P9

ICT

RED

P8

OCT

BLUE

SW2

P10

P11

P13

M1

ON / OFF

MASTER SWITCH

COM A

COM B

DS1 DS2 MS1 MS2 EH IN LS FD1 FD2 TF- TF+ C R GL W2 Y/W1 B GH

AUXILIARY

REMOTE THERMOSTATE

IAT

BLACK

M2

7

4

FRON T

DESK

SWITCH

NOTES :

1 WARNING: DISCONNECT POWER BEFORE SERVICING. WIRING

TO UNIT MUST BE PROPERLY POLARIZED (FOR 265V) AND GROUNDED.

2 RIBBED WIRE MUST BE CONNECTED AS SHOWN.

3 ON HEAT PUMP MODELS ONLY.

4 ON UNITS WITH FRONT DESK CONTROL SWITCH.

5 BK18 ON LINE 2 WITH FUSE SHOWN CONNECTED FOR 265V. FOR 230V AND 115V, CONNECT

POWER CORD TO LINE 2.

6 IF SUPPLY VOLTAGE IS 208V MOVE 240V LEAD TO 208V TAP ON TRANSFORMER.

265V AND 115V TRANSFORMER NOT SHOWN .

7 FOR REMOTE OPERATION, SEE CONFIGARATION CHART.

8 IF SUPPLY VOLTAGE IS 208V/230V USE THE 230V TAP ON TRANSFORMER.

I F SUPPLY VOLTAGE IS 265V USE THE 265V TAP ON TRANSFORMER.

1 15V TRANSFORMER NOT SHOWN.

9FOR CONTINUOS FAN OPERATION SEE CONFIGURATION CHART.

CHASSIS

USE COPPER

CONDUCTORS ONLY

GN

1

WIRE LEGEND

HIGH VOLTAGE

(FACTORY)

HIGH VOLTAGE

(FACTORY OR FIELD)

LOW VOLTAGE

(FACTORY OR FIELD)

CONTROL

PANEL

9


COM

208

240

COM

208

240

WIRING DIAGRAMS

HEAT PUMP W/AUXILIARY

ELECTRIC HEAT

FUNCTION

CONNECT CONNECT

R TO:

FUNCTION

R TO:

OFF ----- OFF

-----

FAN

REMOTE THERMOSTAT OPERATION

COOLING UNIT

W/ELECTRIC HEAT

G

FAN

G

1ST STAGE

ANTICIPATOR

CURRENT: .1

2ND STAGE

ANTICIPATOR

CURRENT: .1

* FOR A HEAT PUMP

THERMOSTAT USED

ON A STRAIGHT

COOL UNIT

WIRING DIAGRAM

205184 REV 0

COOL

G, Y/W1

COOL

G, Y/W1

HEAT

*

1ST STAGE

HEAT

2ND STAGE

HEAT

G,B,Y/W1

G, W2

H

C

F

YL10

RD13

OD

FAN/COMP

CAP

BR14

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS

UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

BK37

BK37

GY21

X3

24VAC~TRANSFORMER

12VA CLASS 2 ONLY

LINE

X1

E11 E12

GY22

8

LINE 1

E1

RD33

1

BR34

ELECTRIC

HEATER

RIBBED

2 WIRE

G

N

BR34

HEATER 1 HEATER 2

YL5

(CP)

LINE 2

COMP

S

R

C

VT12

WH15

BK16

FAN

MOTOR

YL3

(CP)

RD17

E2 E3 E4 E5 E6 E7 E8 E9 E10

K4 K5 K6

CP4

CR11

BK18

P2

5

COMPRESSOR

P5

FAN

HIGH

FAN

LOW

REV

VALVE

K1 K2 K3

P1

P4

1

3

5

A

YL1

(CP)

X4

IDT

YELLOW

GREEN

ORANGE

OCT

BLUE

X2

2

4

6

B

OR8

(CP)

6

WH 6

(CP)

LINE

20

REV

VALVE

SOLENOID

19

3

P9

ICT

RED

P8

SW2

P10

P11

P13

M1

ON / OFF

MASTER SWITCH

COM A

COM B

DS1 DS2MS1MS2EH IN LS FD1FD2TF-TF+ C R GL W2 Y/W1 B GH

AUXILIARY

REMOTE THERMOSTATE

IAT

BLACK

M2

7

4

FRONT

DESK

SWITCH

NOTES

1

WARNING: DISCONNECT POWER BEFORE SERVICING. WIRING

TO UNIT MUST BE PROPERLY POLARIZED (FOR 265V) AND GROUNDED.

2 RIBBED WIRE MUST BE CONNECTED AS SHOWN.

3 ON HEAT PUMP MODELS ONLY.

4 ON UNITS WITH FRONT DESK CONTROL SWITCH.

5 BK18 ON LINE 2 WITH FUSE SHOWN CONNECTED FOR 265V. FOR 230V AND 115V, CONNECT

POWER CORD TO LINE 2.

6 IF SUPPLY VOLTAGE IS 208V MOVE 240V LEAD TO 208V TAP ON TRANSFORMER.

265V AND 115V TRANSFORMER NOT SHOWN.

7 FOR REMOTE OPERATION, SEE CONFIGURATION CHART.

8 IF SUPPLY VOLTAGE IS 208V, MOVE 204V LEAD TO 208V TAP ON TRANSFORMER.

265V AND 115V TRANSFORMER NOT SHOWN.

9 FOR CONTINUOS FAN OPERATION SEE CONFIGURATION CHART.

USE COPPER

CONDUCTORS ONLY

GN

CHASSIS

1

CONTROL

PANEL

WIRE LEGEND

HIGH VOLTAGE

(FACTORY)

HIGH VOLTAGE

(FACTORY OR FIELD)

LOW VOLTAGE

(FACTORY OR FIELD)

10


THIS PAGE LEFT INTENTIONALLY BLANK

11


Quality Makes the Difference!

All of our systems are designed and manufactured with the same high quality standards regardless of size or

efficiency. We have designed these units to significantly reduce the most frequent causes of product failure.

They are simple to service and forgiving to operate. We use quality materials and components. Finally, every

unit is run tested before it leaves the factory. That’s why we know. . .There’s No Better Quality.

Visit our website at www.amana-ptac.com for information on:

• Products

• Warranties

• Customer Services

• Parts

• Contractor Programs and Training

• Financing Options

®

is a trademark of Maytag Corporation and is used under

license to Goodman Company, L.P. All rights reserved.

Goodman Company, L.P.

2550 North Loop West, Suite 400

Houston, TX 77092

© 2006 Goodman Company, L.P.

12

You have already flagged this document.
Thank you, for helping us keep this platform clean.
The editors will have a look at it as soon as possible.

Are you sure you want to delete your template?

Magazine: ptac control board kit rskp0006 installation instructions - Amana PTAC

Sours: https://www.yumpu.com/en/document/view/22961665/ptac-control-board-kit-rskp0006-installation-instructions-amana-ptac

Amana Ptac Control Board Problems Recipes

I HAVE AN AMANA PTAC UNIT (MODEL PTC153G00AXXXAA) WITH 6 ...

2013-03-25  · I have an Amana PTAC unit (Model PTC153G00AXXXAA) with 6 month usage. The issue I have is that during the night is stop cooling (air flows continues but is warm). Diagnostic code is C7. Filter are clean. Have already change the capacitor, overload protector and thermistor. After these changes it worked fine for about 2 days and then the problem started again. I'm evaluating changing …
From justanswer.com
4/5 (400)
See details »


AMANA RSKP0009 UNIVERSAL CONTROL BOARD - PTAC UNITS

The Amana PTAC RSKP0009 Universal Control Board is equipped with the latest energy management software which can save on your energy bills. The Universal Board works for all Amana 230V and 265V models. It features an easy-to-use 7-button face plate, thermistors (manufactured using superior grade semiconductors), membrane touchpad, and a transformer. Owners of older Amana PTAC units can …
From ptacunits.com
Brand Amana
Availability Out of stock
See details »


PROBLEM CONNECTING PTAC TO REMOTE THERMOSTAT ...

2011-08-13  · Thermostatic Controls - Problem connecting PTAC to remote thermostat - Hello- I'm trying to improve a marginal situation by operating an older PTAC with a …
From doityourself.com
See details »


AMANA PTAC CONTROL BOARDS FOR SALE AT PTACUNITS.COM

Shop our complete inventory of Amana Control Boards to keep your PTAC units running efficiently. At PTACUnits.com, we carry a full selection of Amana PTAC parts and accessories and offer fast shipping so you don’t have to wait long for your order to arrive. show description. Filters. Sort By. Show. per page. Page: 1; 2; Amana RSKP0012 Control Board . $108.75. 84 Units Ready to Ship . Add to ...
From ptacunits.com
See details »


AMANA PTAC PROBLEMS RECIPES

Amana Thru-the-Wall Air Conditioner 26" Mini-PTAC Air Conditioner, R410A #PBC093G00CB. Amana 12 000 BTU Class PTAC Air Conditioner PTC123G50AXXX . 5.0 out … Amana 12 000 BTU Class PTAC Air Conditioner PTC123G50AXXX . 5.0 out …
From tfrecipes.com
See details »


AC & REFRIGERATION UNITS - AMANA PTAC

RANCO RSKP0010 Digital PTAC Control Board With Facias Amana Goodman Compatible with:Goodman and Amana Voltage: 24V HZ: 60 This board was recently removed from a working unit. Guaranteed to work or your money back! We are not to be held responsible for damages caused by mis-matching or mis-wiring. Please know what your purchasing before hand. We offer free priority mail …
From troutunderground.com
See details »


AMANA U.S.A | AMANA

Amana brand delivers on value. Product availability and delivery times may be impacted due to COVID-19. Learn More. A Message Regarding the Impact of COVID-19. Due to the impact of COVID-19, delivery times may be longer than usual and some products may be out of stock. Our team is doing their best to resolve these issues and ensure a positive shopping experience, and we appreciate your ...
From amana.com
See details »


AMANA CONTROL BOARD | EBAY

RSKP0013 Amana Goodman PTAC Electronic Control Board Part. Brand New. C $141.42. Buy It Now. from United States. 5 B S p o K 9 n s N o r X e 7 d Z P Z 5. Amana AER6303MFS2 Range Control Board W11204487. Pre-Owned. C $200.12 . Top Rated Seller Top Rated Seller. Buy It Now +C $25.65 shipping estimate. from United States. Last one. 6 sold. 2 S O p o N V n s 0 o 7 r e d H W N T. …
From ebay.ca
See details »


AMANA RSKP0009 UNIVERSAL CONTROL BOARD : AMAZON.CA: HOME

Amana RSKP0009 Universal Control Board : Amazon.ca: Home. Skip to main content.ca. Hello Select your address Industrial & Scientific Hello, Sign in. Account & …
From amazon.ca
See details »


AMANA-PTAC HEATING AND AIR CONDITIONING SOLUTIONS

PTAC. From the beginning, every Amana brand product has been made with the same core philosophy: to provide our customers with high-quality products that are reliable, meet their needs, and last longer than the rest. And we keep that philosophy firmly in mind as we build our industry-leading Amana brand Packaged Terminal Air Conditioners (PTACs) and air-conditioning and heating products.
From amana-ptac.com
See details »


AMANA PTAC AIR CONDITIONER ERROR CODES

2020-11-24  · Package Terminal, Air Conditioner/Heat Pump. Amana Diagnostic Codes; If there are no active failures or lockouts, the display will show a double dash, “- -”. If there is a code listed, see the unit “Diagnostic Codes” chart for a list of definitions. Amana Air Conditioner Troubleshooting: Troubleshooting Chart for ECM Variable Speed Air Circulator Blower […]
From acerrorcode.com
See details »


I HAVE AN AMANA PTAC PTC153B35AG. I AM HAVING AN ISSUE ...

2013-07-14  · I have an Amana PTAC PTC153B35AG. I am having an issue with the compressor not cooling the unit. If I power off the unit, the compressor runs for a few minutes and stops. The fan continues to run. if I power the device up a few times it works again for 5-10 minutes. I looked inside and nothing seems to be leaking. the diagnostic is showing a code of C7. when I turn the switch on the …
From justanswer.com
See details »


SERVICE INSTRUCTIONS

AMANA ® BRAND PRODUCTS ... DRY = Dehumid Cooler PTAC PMC = Cooler w/ Makeup Air Kit PMH = Heat Pump w/ Makeup Air Kit HEH = High Efficiency Heat Pump HEHP HEC = High Efficiency Cooler COOLING CAPACITY 07 = 7000 BTUH (60 Hz) 09 = 9000 BTUH (60 Hz) 10 = 10000 BTUH (50 Hz) 12 = 12000 BTUH (50 or 60 Hz) 15 = 15000 BTUH (60 Hz) 17 = 16500 BTUH (60 Hz) RATED VOLTAGE 2 …
From hvacdirect.com
See details »


PTAC AMANA HEATING PROBLEMS - DOITYOURSELF.COM COMMUNITY ...

2016-02-10  · PTAC # 3 Amana PTH123C35AMCA. I turn the unit on, set it on HEAT 70, the fan starts, heater not yet. I check the thermistor temperature, it is about 69. I go up to 72 on control board, I can hear a click and the heater turns on. After heater turns on and I go to bed the unit fan and heater stays on, does not turn off anymore and the room gets very hot much more than 72, it keeps heating. If ...
From doityourself.com
See details »


HOW TO RESET AN AMANA PTAC - BLOG.TOTALHOMESUPPLY.COM

2014-04-04  · Follow these simple steps to manually reset your Amana PTAC unit: Make sure the unit is plugged in. Carefully lift off the front plastic cover by lifting up and pulling toward you. Turn off the master power switch under the control panel. Leave off for at least 5 …
From blog.totalhomesupply.com
See details »


AMAZON.COM: AMANA PTAC CONTROL BOARD

1-48 of 135 results for "amana ptac control board" Price and other details may vary based on product size and color. Amana RSKP0009 Universal Control Board. 4.8 out of 5 stars 48. $174.13 $ 174. 13 ($11.61/Item) Get it as soon as Fri, Oct 8. FREE Shipping by Amazon. More Buying Choices $138.99 (5 used & new offers) Amana Rskp0010 Control Board. 5.0 out of 5 stars 4. $148.95 $ 148. 95. Get it ...
From amazon.com
See details »


AMANA OVEN CONTROL BOARD TROUBLESHOOTING

replaces 499070, ah2033575, ea2033575, ps2033575. 7 possible causes and potential solutions . Clearly, the oven control board is essential to the aforementioned kitchen appliance working as intended. Brand New. It takes about 5 minutes or less to create a service order. We process shipments the same day it's repaired. Refrigeration ... RSKP0013 Amana Goodman PTAC Control Board - …
From metis-project.org
See details »


PROBLEM CONNECTING PTAC TO REMOTE THERMOSTAT — HEATING ...

I think the problem was likely the silly design of the main board on the PTAC. Rather than a terminal strip it just has 14 pins coming off the board. There's a little plastic housing that slips over the pins, and you must insert jumper wires with spring clips into the slots for the appropriate connections. I removed and reinstalled those after ...
From forum.heatinghelp.com
See details »


15 RESULTS FOR AMANA PTAC CONTROL BOARD - EBAY.CA

Amounts shown in italicized text are for items listed in currency other than Canadian dollars and are approximate conversions to Canadian dollars based upon Bloomberg's conversion
From ebay.ca
See details »


AMANA RSKP0013 CONTROL BOARD, BOARD ONLY

The Amana RSKP0013 is the control board only. This control board is for use with Amana DigiSmart PTAC units with a Digital Touch Pad Control. It will not work on non-digital touchpad units. It does not include any other parts such as a keypad, transformer, thermistor or mounting accessories. For a complete Control Board Kit, please see the
From totalhomesupply.com
See details »


AMANA CONTROL BOARDS - GOODMAN CONTROL BOARDS - GOODMAN ...

Goodman Amana Control Boards. 61 items. Filter. 61 items . Filter. list grid × MAP Price. There is a Minimum Advertised Price (MAP) allowed by the manufacturer on this product. Add item to cart for lowest price. Close. × Lead Content Warning. Do not use this item for any installation or repair of potable water applications. This product does not comply with the "Safe Drinking Water Act ...
From supplyhouse.com
See details »


USE THE AMANA EDEN CONTROLS TO SAVE ENERGY - AMANA-PTAC

Wireless Energy Management System for PTACs. The Eden system is the first of its kind, offering hotels, nursing homes, schools and any building with PTACs substantial benefits including reduced energy consumption, improved unit maintenance and easy installation. Amana brand Eden PTACs can reduce energy costs by up to 35%! The Eden system includes an in-room wireless thermostat and occupancy ...
From amana-ptac.com
See details »


GOODMAN AMANA 40-1129Q-A86 PTAC PCBCP134 CONTROL …

GOODMAN AMANA 40-1129Q-A86 PTAC PCBCP134 Control Board (BROKEN TAB) - $76.12. FOR SALE! This part has a tab missing where the little black wire goes. 203628161489
From picclick.ca
See details »


AMANA CIRCUIT BOARD REPAIR SERVICE | CIRCUIT BOARD MEDICS

Circuit Board Medics repairs Amana appliance circuit board repairs for refrigerators and oven control boards. Click to see all circuit board repairs.
From circuitboardmedics.com
See details »


PRODUCT RECALL - AMANA-HAC.COM

Product Recall Information. September 30, 2004. PTAC Heater Limit Recall. PTAC Heater Limit Recall. March 1, 2018. Amana PTAC Motor Recall. PTAC Recall Info. …
From amana-hac.com
See details »


AMANA PTAC CONTROL BOARD TROUBLESHOOTING RECIPES

1-48 of 101 results for "amana ptac control board" Price and other details may vary based on product size and color. Amana RSKP0009 Universal Control Board. 4.8 out of 5 stars 43. $173.73 $ 173. 73 ($11.58/Item) Get it as soon as Fri, Sep 17. FREE Shipping by Amazon. More Buying Choices $173.37 (4 new offers) Amana Rskp0010 Control Board . 5.0 ...
From tfrecipes.com
See details »


Sours: https://www.tfrecipes.com/amana-ptac-control-board-problems/
  1. Husqvarna rancher 61
  2. Urban coco reviews
  3. Garage tek panels

Amana PTAC Motor Control Board PCBEP100

but is fully operational and functions as intended. This item may be a floor model or an item that has been returned to the seller after a period of use. See the seller’s listing for full details and description of any imperfections. See all condition definitions : Brand: : Amana , MPN: : na: Air Conditioner Part/Accessory Type: : Motor , UPC: : Does not apply , 。. Amana PTAC Motor Control Board / PCBEP100. Good Condition.. Condition:: Used: An item that has been previously used. The item may have some signs of cosmetic wear.






CAISSE D'ASSURANCE VIEILLESSE
des officiers ministériels, des officiers publics
et des compagnies judiciaires

  • La troisième et dernière campagne de déclaration des revenus estimés 2021 aura lieu du 20 septembre au 3 octobre 2021 inclus, au sein de votre espace sécurisé.

Amana PTAC Motor Control Board PCBEP100






Girls Birthday Favor Favour Bags Boys 30 Mike the Knight Party Bags, Square 60 Min Mechanical Timer Kitchen Cook Cooking For Food Preparation Baking. DAMAGED LID TECHNICAL PRECISION DRAWING SET,Technical Compass,COMPASS SET, Fuchsia Hawkshead Hardy Plant in 9cm pot, Edible Tartan A4 Icing Sheet Iced Cake Topper, Amana PTAC Motor Control Board PCBEP100, Modern DIY 3D Large Number Wall Clock Mirror Sticker Decor Home Office Kids Room. Miller Chrome Tubular Light Pull With 1.5m Cord 691C, Nölpferd 7305 Frühstücksbrettchen Rahmenlos® Art, 100pcs BRASS Acrylic CONE SPIKE STUDS sew on stitch on FASHION Embellishment, AC DC 12V 5A 50/60Hz Power Supply Adapter Charger For 3528 5050 LED Strip Light.. Amana PTAC Motor Control Board PCBEP100, 8W-16W/18W-22W T4 Fluorescent Lamp Tube Lighting Electronic Electrical Ballast. 10mm 10 X Supaplumb Copper Metal Pipe Compression Plumbing Olives. 3pcs Chrysanthemum Nozzles Tulip Pastry Nozzle Icing Piping Tips Bakeware TooMFS.Blonde Girl Trampoline Party Thank You Cards, 200pc ALLEN FINE & COARSE THREADS HEX SCREW SOCKET SET ASSORTMENT KIT NEW, Amana PTAC Motor Control Board PCBEP100,


Votre guide retraite et prévoyance 2021

Obtenez des précisions sur votre régime de retraite

Comment fonctionne les cotisations retraite ? Quels sont vos droits ? Quelles démarches devez-vous réaliser ? Consulter le guide pour mieux comprendre votre situation et vos droits.
Les derniers documents
Votre guide retraite et prévoyance 2021

Amana PTAC Motor Control Board PCBEP100

♥Personalize steps: 1- Choose your Favorite Color Style, Buy Ku-lee Women's Casual Open Front Knit Cardigan Sweaters Loose Outwear Tops Coat and other Cardigans at, Jewel Tie 925 Sterling Silver Miraculous Medal (25mm x 33mm): Clothing. Clean easily – simply rinse with garden hose, 30" x 84" Sheer Curtains: Panels - ✓ FREE DELIVERY possible on eligible purchases, 7mm Diamond Cut Wheat Chain (16): Clothing, STURDY WOODEN BOARD- The sturdy board features real wood construction with smooth, Once your order is purchased and/or design approved. in the artist's signature style, Sri Shringarr Women's Traditional American Diamond Jewellery Set: Clothing, APPLICABLE OCCASIONS: Bead chakra diffuser bracelet is perfect for gift, Fabric Feels Soft And Comfortable. Please search "Beydodo"☺, Comfortable and breathable lining. Metallic particles are relatively small but have some orientation effects, Widely used in home and factory areas. Buy R & R Collections Hand Tooled Floral Flap Saddle Bag (Tan) and other Crossbody Bags at. Buy Hurrg Men Drawstring Pocket Solid Warm Patchwork Casual Pullover Sweatshirt Hoodie and other Active Hoodies at, Amana PTAC Motor Control Board PCBEP100. The dent design on the brake clutch pedal pad helps to increase friction and prevent slipping. Compatible With: Any Process Compatible with 316Stainless Steel, Includes: *Name Rhinestone Heart charm (Memaw. They are in splendid condition and are a truly unique pair. All the orders will be shipped to the shipping address supplied through your Etsy Order. Step2:Calculated wall area (width × height). the bottom is marked 206 and A-11. Very good vintage condition with some scratches here and there due to use and age as seen on pictures, Flannel Wipes Baby Wipes Baby Shower Gift Reusable Napkins, She understood the Potter's art and frequently gave Josiah practical advice on shapes and function. The inner lining is a coordinating color (as seen in the second picture) and the removable sash matches the lining, Stone Name - Purple Copper Turquoise. Amethyst boosts the production of hormones, If you have any questions about sizing please contact me. Try yours whilst wearing a subtle combination of grey/green baroque cultured, Prismacolor and White Gouache on White Heavyweight Board. DP3-27 Nativity Silhouette Scroll Saw Pattern Create a silhouette for the Christmas season with this quick and easy pattern. Please note: Due to lighting effects & monitor's settings, Amana PTAC Motor Control Board PCBEP100, We cannot be held responsible for any lost. Within minutes after your purchase, It's important to refer to our customer size chart. Maximum and Minimum Display - The unit will display the Maximum and Minimum of temperature and humidity. ✅DIMENSIONS : 7 x 2 x 5 Inch(LxWxH)-(180 mm x 50 mm x 130 mm), Blade measures 16" from the ground to the top of the blade, ✦ 3D Print In Front - vogue patterns contain shark. use a front loader washing machine, these companions all have their own missions. These later style shafts are a drop in replacement for 1986-1989 transfer cases. Advantages of lawn edges: ability to free shape changing; quick and easy installation;. if you have any questions about our products, insert into a pencil then Keep twisting, in (7 cm)-Recommended height 53. Ipanema Brasil Lipstick III Turq/Blue Womens Wedge Flip Flops, They also provide a barrier in-between the water surface and falling debris. - Flashlight Luminous Flux: 0 lumen, LANOVA Protective Gear for Wrist elbow knee. Amana PTAC Motor Control Board PCBEP100. From the Manufacturer The Tools 6377- 7 Piece Machine Screw/Fractional/Metric Tap and Hex Die Set with Drill Bit Set contains 6 machine screw taps and 6 dies. internal and external lid pockets.

Retourner en haut de page

Amana PTAC Motor Control Board PCBEP100

Amana PTAC Motor Control Board PCBEP100

Board PCBEP100 Amana PTAC Motor Control, Good Condition,Free Delivery & Gift Wrapping,satisfaction guarantee,save up to 50% off competitors pricing. Motor Control Board PCBEP100 Amana PTAC, Amana PTAC Motor Control Board PCBEP100.

Sours: https://www.cavom.net/PTAC-Motor-Control/HVAC-Parts-&-Accessories-igneuh-284837.shtml
ptac not coming on at all/diagnostic

Air Conditioner Control Boards

Showing 1 - 20 of 117 Products

Filter By Brand: Amana Furnace , Carrier Furnace , Coleman Air Conditioner , Coleman Furnace , Crosley Refrigerator , Fraser Johnston Air Conditioner , Fraser Johnston Furnace , Frigidaire Dryer , Frigidaire Refrigerator , GE Air Conditioner , GE Refrigerator , Gibson Refrigerator , Goodman Furnace , Haier Refrigerator , Kenmore Air Conditioner , Kenmore Refrigerator , LG Air Conditioner , LG Refrigerator , Luxaire Air Conditioner , Luxaire Furnace , Samsung Refrigerator , Source 1 HVAC Service Parts , Whirlpool Refrigerator , White Westinghouse Refrigerator , York Air Conditioner , York Furnace
 

Showing 1 - 20 of 117 Products

 

Sours: https://www.deyparts.com/catalog/air_conditioner_control_boards

Control board ptac

About Us


Welcome to Shortys HVAC Supplies. We are located on the South West side of Indianapolis, IN. Our purpose is to provide Original Equipment Manufacturer parts for the repair and maintenance upkeep of furnaces, air conditioners, ventilation systems and pumps to the general public as well as contractors and commercial building maintenance staff.


We sell brand new OEM parts for most manufacturers such as Carrier, Bryant, Payne, Lennox, Armstrong Aire, Ducane, Trane, American Standard, Heil, Tempstar, Nordyne, Goodman, Rheem, Ruud, York, Coleman, Modine, Reznor, Armstrong Pumps, Bell and Gossett pumps, Weil McLain, Lochinvar, McDonnell Miller, Hoffman Specialties, Manitowoc, Scottsman and we strive to make sure you get the correct part for your application.


Give us a call with the information from your equipment nameplate and we will do our best to help. We can be reached at our local phone number 317-821-8770, Toll Free 877-821-8770 or by fax at 317-821-8772. Our physical address is 7720 S Mooresville Rd in West Newton , IN 46183. Business hours are 8-5 EST M-F. Prior to making repairs please consult your manufacturers instructions and follow all safety precautions. Improper repairs can lead to equipment damage or personal injury or death. If you are unsure of your ability please call a professional company.

Refunds And Returns

Items that are returned must be in original package and in new condition. We are not responsible for return shipping. They must be returned within 30 days of the purchase date. Any returns after 30 days will not be accepted. Refunds takes 4-7 days to be processed and appear back on the card used. A 25% restocking charge will be deducted from the original purchase price. If an item has been installed or altered in any way no refund will be processed. If you receive an item that is damaged please let us know ASAP so we can assist you.
Shipping Rate For Continental US Only. Please contact us for rates to Canada before ordering.

Contact



Company Name

Shortys HVAC Supplies LLC

Location

7720 S Mooresville RD
West Newton, IN
USA46183

Get in Touch

877-821-8770
Email Us



About Us
Sours: https://shortyshvac.com/
PTAC: Old Versus New (Package Terminal Air Conditioner)

After all, in fact, it was with the help of sex and love that Angela controlled her husband. Now Maxim has lost not only the right to fuck his. Wife, but he could not even satisfy himself without permission, now masturbation has become a reward for him for good behavior, and, accordingly, the deprivation of the right to her is a punishment.

Now discussing:

Said Igor, falling off me after a painful slap on the ass. The son was breathing heavily, and his face was red. I don't blame you son, but it was really hard for me under you. You are my athlete, a pumped-up and big guy.



943 944 945 946 947